Every 3 LEDs are controlled by one external WS2818 chip as one single pixel, every 3 LEDs are cuttable.

The advantage of WS2818 LED Strip

• Signal break-point continuous transmission  .
• When one of the pixels is broken,it does not affect another led work.
• With the controller,any flash effect can be achieved.
• The price is close to WS2811,but has breakpoint continuous transmission more than WS2811.

Specifications: 

Input voltage:   DC12V

Power:   7.2watt/meter, 36 watt/roll

LED Chip Model:   SMD 5050 RGB

LED resource:   WS2818 LED

IC Type:   WS2818 IC (1 IC drives 3 led chip)

Qty of LED:    30 leds/meter & 60 leds/meter Available

Qty of IC:   10 pixel/meter & 20 pixel/meter

Cuttable:   every  3 LED is cuttable

Dimensions:    L500cm(196.85 in ) x W1.0cm(0.39 in ) x H0.25cm(0.1 in )

PCB color:   WHITE

Protection rate:   Non-waterproof  IP20 or IP 65( gel coating) IP67 waterproof (sealed in silicone tube) 

Colors:   Full color RGB, dream color changing; 

Grey scale:   256

Bits/color:   8-bits/color;total 24bit for RGB color

Average Life (hrs):   50000 Hours

Certification:   CE,FCC,GS,SAA,RoHS,CCC

Beam Angle: 120 degrees

1, WS2818 light bar for RGB three-channel phantom light bar, LED driver dedicated control circuit.2, 3 LED beads in series to form a single pixel point, can be individually point control.

3, break point continuity, the light bar any one pixel point damage does not affect the other pixel points, while not accruing the line waveform distortion.

4, voltage 12V power supply, maximum withstand voltage 14V.

5, any two pixel transmission distance of 5 meters (the specific transmission distance to the site signal line and environmental interference varies).

6、Signal is serial double signal line cross cascade interface, transmission through cross signal.

7, PWM console can be adjusted to 256 gray levels, a total of 16777216 luminous colors can be adjusted.

8, when the refresh rate of 30 frames / second, the number of low-speed mode cascade not less than 512 points, high-speed mode cascade not more than 1024 points.

They come in 5-meter reels with a 4-pin JST SM connector on each end. 

To Power a full roll of this lpd8806 strip, You must use at least 5V/10A power supply, do not use higher than 6V or you will destroy the entire strip.

Technical specs (newer LPD8806 type):

• 16.5mm (0.65″) wide, 4mm (0.16″) thick with casing on, 62.5mm (2.45″) long per segment
• 32 LEDs per meter
• Removable IP65 weatherproof casing
• Maximum 5V @ 120mA draw per 2.5″ strip segment (all LEDs on full brightness)
• 5VDC power requirement (do not exceed 6VDC) – no polarity protection
• 2 common-anode RGB LEDs per segment, individually controllable
• LED wavelengths: 630nm/530nm/475nm
• Connector: 4-pin JST SM
• waterproof level: not waterproof, drip glue (IP65), casing (IP67), casing solid grouting (IP68), etc.
• FPCB board size: width: 15mm, thickness: 3mm;
• FPCB color: white, yellow, black (except the white need to be customized);
• Packaging: 5 m / roll, back 3M adhesive behind the light bar, electrostatic bag package;
• Weight: 0.32g/roll;
• Boxing: 50 rolls/ctn Box size: 450*330*310(mm), total weight: 17KG.
• We can provide a matching illusion controller and power supply

◆Installation method and precautions◆

 1、Indoor installation: LED strip light for indoor installation is relatively simple because it does not have to withstand the wind and rain. Installation can be directly torn off the 3M double-sided adhesive surface sticker on the back of the strip, and then the strip is fixed in the place where it needs to be installed according to the flat on it. If you meet the corner of the strip is too long and too short, the LED strip can be cut or welded at any point in each group with scissors marking the tangent line for individual use.

2, outdoor installation: outdoor installation because it will be subject to wind and rain, can not be fixed with 3M adhesive, so outdoor installation often use the slot fixed way, the need to cut and connect the place, the same method, and indoor installation, just need to be equipped with an additional waterproof adhesive to consolidate the waterproof effect of the connection point.

3, the power supply connection method: LED illumination strip general voltage DC5V, so you need to use a switching power supply, the size of the power supply according to the power of the LED strip, and the length of the connection to determine.

4、Controller connection method: LED runner strip and RGB full-color strip need to use the controller to realize the illusion effect, and the control distance of each controller is different, generally speaking, the control distance of simple controller is 10 to 15 meters, the control distance of remote controller is 15 to 20 meters, and the longest distance can be controlled to 30 meters. If the LED strip is connected to a longer distance, and the controller can not control that long, then it is necessary to use a power amplifier to tap. 

 ◆Warranty and description◆

 1、The warranty period of this product is 2 years; replacement and repair within the warranty period, but does not include damage caused by man-made damage or overload work.

2, can really achieve 3% light decay within 1000 hours, the service life of 80,000-100,000 hours, please compare the quality of similar products in the market.

3, can be made according to customer requirements into any length and the required number of lamp beads, welcome to call for advice!

Dream color lighting, Match use controller can appear colorful curtain-up/ flow water/raindrop/jump flash and so on hundreds of lighting effect, 

you can also edit animation effects by Coreldraw/Flash/LEDEdit software. the city lighting project, entertainment, and leisure places lighting. It’s very easy to program

Remark:

The price is only Led Strip, Not Included Power Supply or Led Controller!

WS2811 Must Use DC12V Power Supply AND Led Controller to Control!

Every 0.5meter with solder joints, please note! 

PCB Color:  

White: White PCB;  Black: Black PCB 

Protection Grade: 

(1) IP30 — No waterproof, for indoor use 

(2) IP65 — Silicone coating, easy cut, outdoor use  

(3) IP67 — Silicone tube, need to reseal after the cut, outdoor use 

(4) IP68 — IP65+IP67, can work underwater ( if you need we can make it for you ! ) 

Product parameter:

(1) Working Voltage: DC 12V

(2) LED Source: SMD 5050 RGB

(3) LED Chip: Epistar  

(4) LED QTY: 48 LED/M

(5) IC QTY: 16Pcs/M

(6) Power: 6 W/M

(7) Grey Scale: 256 / Color

(8) Cutability: 3 led / cutting ( External 2811 ic, 1 ic control 3 LED )

(9) Beam Angle: 120 °

(10) Color Mode: 133Pattern & 100 Speeds

(11) Dimension: 5000mm x 10mm x 2.4mm

(12) Packaging: 5m / roll 12v ws2811 RGB strip + 3 pin connector

(13) Warranty: 2-3 years 

FEATURES:

1. Low-power consumption, 80% energy savings
2. 3M VHB Adhesive ensures LED Strips last both indoors & out
3. Waterproof 3-pin barrel connectors
4. Extra power and ground wires for easy power distribution
5. Long lifespan, at least 50,000 hours
6. 12V over 5V DC Power for longer runs of LEDs before power distribution required
7. Quick and easy installation
8. Compatible with WS2811, WS2812 & WS2812B Controllers
9. Flexible PCB  ( IP30, IP65)  With 3M adhesive tape on the back for easy installation. 

       10. Energy saving and environmental protection. 

      11. High brightness 5050 SMD LED light strip. 

12. Solid-state, high shock, or vibration resistance. 
13. Low power consumption, high intensity. 
14. Match the RGB controller and power supply system. 
15. Wide viewing angle. 
16. Available in various single and RGB colors. 

Applications:

      Ideal for party, wedding, festival, holiday, Xmas, Halloween, light sculpture, decorative figure, active signs, displays, shop windows, and storefronts, bar, nightclub, street, sidewalk, deck, park, porch, staircase, railing, ceiling, or driveway

Power Supplies and LED Strip Kits are available soon!

-Programmable led strip lights

This 5-meter roll has 60 LEDs & 36LED per meter on a white-colored strip.

This is a roll of addressable (TM1923) RGB LEDs. The LEDs are factory-calibrated to ensure you have consistent colors all the way along your strip.

The RGB addressable led strip is weather-sealed in a flexible plastic jacket (easily removed, if desired) and terminated at each end with a 3-pin plug, and two additional power leads if high current is required.

Long strips can require a lot of currents! Make sure you’re using a power supply that is capable of running your project. We’ve listed the maximum current that these LEDs consume (full-brightness white) but for a typical, colorful display the current required is usually a lot lower. If you decide to go with a smaller power supply, experiment with the length of strip you need to find out its true current requirements. 

For those of you who are looking to plug multiple of these strips together, we have these 3-pin Pigtail Connectors.

Overview

• Brand: MSH LED 
• Manufacturer: MSH LED Lighting
• Package Dimensions: 46*46.5*26cm
• Number of Lights: 300
• Voltage: 24 Volts
• IC: TM1923
• Controller Required?: No
• Type of Bulb: SMD5050 RGB LED
• Item Weight: 310 g

• 5 meters LED Strip only 1 x 5 Meter LED Strip only (300leds), no power adaptor. If need to light up and control the LED Strip, another DC24V power adaptor. Please refer to 5 meters kits (That kit include 5meters LED Strip, 1 x DC24V Power adaptor) ;
• No need for a Controller, It is automatic self-control.
• 24V Power Adaptor 24V power adapter directly, easy and convenient.
• InstallationStrong 3M adhesive tape on the backside of PCB for installation.

【24V Addressable LED Strip】Dream Color SMD 5050 RGB LED Strip 60LEDs/m, Each 5cm (3LEDs) could be cut, with digital IC TM1923 to realize color changing, chasing, flashing, running, etc., Fascinating, Dynamic, Wonderful lighting, Much better lighting effects than regular RGB LED Tape. Non-waterproof IP20 for indoor and dry environments using only. 

【24V Power Adaptor】The LED Strip voltage is DC24V, the 24V power adapter with DC connector could be easily and conveniently connected with the magic controller. 

【How to install】Strong 3M adhesive tape on the backside of PCB for installation. 

【How to light up】3 steps to light up the led strip: 1st, 24V power adapter connect with a magic controller with DC connector, and Magic Controller connect with the dream color LED Strip with a connector on the box. 2nd, Power Adapter to be powered on ; 

【5 meters LED Strip package】 > 1 x 5 Meter LED Strip only ; > If need to light up and control the LED Strip, another DC24V power adaptor and digital RGB led strip controller must be ; > Please refer to 5 meters kits (which include 5 meters LED Strip, 1 x DC24V Power adaptor.

Product Model: S020090-SM16703RGB.  

Voltage: DC12V. 

Power: 21.6W/M, 

IC Model: SM16703  

Display grayscale level: 256. 

Lamp beads: 5050RGB  

Pixel point: 30Pixels/M, 

Number of LEDs:90LEDS/M 

PCB width:20mm, 

IP Rate: IP23,IP65,IP67,IP68

Our company produces LED full-color soft strips using light decay slow, high brightness imported chips as the light source. Using SOP-8 illusion driver IC as the driving source, RGB light beads have 256 levels of gray, which can send out different colors, and the product luminous brightness is the highest of similar light beads.

Cutting and welding are convenient and free and can be cut and welded along the above cut line to meet the customer’s requirement of various light bar lengths. 

The unique design of the FPC circuit board without hole drip glue does not leak glue, the board is simple and not easy to failure, using the soft FPCB board as the substrate, can be docking, bending, cutting, and any fixed concave and convex surface. 

Both ends of the humanized reserved joints, better and more convenient to use, long life, the average life of 40,000 hours.

 Control principle: an IC control an LED to form a circuit (a group), the controller through the control IC to control the circuit inside the FPCB, so as to control the LED strip change different effects; such as flashing, chase, jumping change, clockwise running horse, counterclockwise running horse, monochrome running horse, color-changing running horse, single chase from beginning to end, flowing water, simulation, lightning, etc.; this light strip change effect is not limited to the current controller built-in 128 kinds of effects, according to customer needs, their own preparation; row into the form of the screen can display text, letters, pictures, animation, etc.

Advantages

1. PWM refresh rate: 1.2kHz, transfer speed 800k bps

2. It comes in 1 meter per reel with a 3Pin female/male JST SM connector on both ends and separated Power / Ground Wires. Customized length is workable.

3.12V and 24V optional.

4.2 ounce PCB board with the double copper layer.

5. double sides membrane covers the PCB board. make sure the copper no drop from the PCB board

6. Flexible PCB material. ever 3 LEDcan be cut with 12V, every 6 LEDcan be cut with 24V,

7.90 LEDs per meter. 12V low voltage input, don’t over 13V, otherwise, you will destroy the entire strip.

8. Controller System： SD controller, DMX controller, Artnet, and so on. 

9. Installing: screw+silicon clip and 3M adhesive on the backside for sticky

Application

1, The polygon wall of the hotel, night club, KTV, and other places, the teardrop row ceiling is decorated to bring up the atmosphere, 

2, buildings, advertising walls, signboards, festivals, and other decorative areas of the city to beautify, brightening effect 

3, canopy and bridge arch edge, amusement parks, theaters, aircraft cockpit lighting 

4, home decoration lighting (stairs, door frame, bar, wine cooler, closet, TV cabinet, DIY home decoration.) 

5, car beauty (car body, car low…)

6, with iconic buildings building pavilion, bridges, parks, and other contours of the outline, embellished lighting effect

1、Product Model: S010060-SM16703RGB

 2、Voltage：DC12V

 3、Power：14.4W/m

 4, IC model: SM16703, 1903, 2811 (optional)

 5、Display gray level: 256

 6、Lamp beads: 5050RGB (optional monochrome)

 7、Pixel point: 20PIX/m

 8、Number of lamp beads: 30/48/60LED/m

 9、Board width: 10MM

 10、Waterproof grade: bare board (IP23), drip adhesive (IP65), casing (IP67), potting (IP68)

 11、Working temperature: -40℃~80℃

 12、Service life: 50Kh

Product advantages.

1, high brightness and no glare: the company’s digital pixel tape using slow light decay, high brightness imported chips as the light source.

2, energy-saving and safety: the product uses a DC12V low-voltage circuit design, safe and stable.

3, rich light effects: can generate light effects such as flashing, chasing, running horse, flowing, flashing, fading, meteor, jumping, clockwise running horse, counterclockwise running horse, single color running horse, color-changing running horse, single chase from beginning to end, simulated lightning, etc., the effect of changes in this light bar is not limited to the current controller built-in 300 kinds of effects, can be written according to customer needs, arranged in the form of a screen can display text, letters, pictures, animations, etc. pictures, animations, etc..

4, soft and thin: the use of FPC (flexible circuit board) to do assembly circuit board, with SMD LED and the original assembly, so that the thickness of the product is only the thickness of a coin, accounting for little space, and can be cut at will, FPC material is soft, can be wound at will, can be moved at will in three-dimensional space and winding without breaking, suitable for irregular places, and the use of space is small, suitable for advertising, lighting decoration, any combination of various effects. lighting decoration, any combination of various patterns.

5, easy to install: each group of LED can form a circuit, can be cut off and welded along the above cut line arbitrarily to meet the needs of customers required by the length of various light bars, flexible and convenient cutting so that the construction operation is simple, the back paste 3M adhesive can be easily fixed, ultra-thin design, low-temperature light source, so that the product in the installation process of the choice of auxiliary materials with more flexible;

6, green environmental protection: with small power consumption, generate little heat, low loss, no radiation, maintenance-free, etc., is a new generation of green and environmentally friendly high-tech products.

7, long life: the average life of 50,000 hours, and installation, available to more than 7 years, a once-and-for-all choice. 

Scope of use.

1, urban contour lighting: buildings, villas, bridges, signboards, advertising light boxes, luminous fonts, Christmas landscape, and other decorations.

2, public lighting illumination: hospitals, villas, bridges, parks, gymnasiums, swimming pools, airports, subway stations, stations, etc.

3, home dark slot inset: door frame, bar, wine cabinet, closet, TV cabinet, ceiling dark grid, etc.

4, irregular design body decoration: shopping malls, hotels, nightclubs, KTV, and other places of polygonal walls, ceiling recesses, steps, and booths, etc.

5, car beauty: car body, car bottom, unicycle, balance car, etc.

6、Decoration on shoe lights, toys, and entertainment products.

Application areas.

1, hotels, nightclubs, KTV, and other places of polygonal walls, teardrop rows of ceilings, up to decorate to set the atmosphere.

2, buildings, advertising walls, signboards, festivals, and other decorative areas of the city to play a beautifying and lighting effect.

3, stairs, door frames, bars, wine coolers, closets, TV cabinets, DIY home decorative lighting.

4, with iconic buildings building pavilion, bridges, parks, and other contours of the outline, play a decorative lighting effect.

5, lighting signals, such as a variety of luminous indication signs.

6, canopy and the edge of the bridge arch, amusement parks, theaters, aircraft cockpit lighting.

Installation methods and precautions.

1, indoor installation: 12v addressable RGB strip lights for indoor installation are relatively simple because they do not have to withstand the wind and rain. Installation can be directly torn off the 3M double-sided adhesive surface sticker on the back of the strip, and then the strip is fixed in the place where it needs to be installed according to the flat on it. If you encounter corners or the light bar is too long and too short, LED strips can be arbitrarily cut or welded at each group with scissors marking the tangent line for individual use;

2, outdoor installation: bare board strip is not waterproof, drip tape moisture-proof waterproof drop but can not be immersed in water, casing glue lamp with waterproof function can be immersed in water, outdoor installation because it will be subject to wind and rain, can not be fixed with 3M adhesive, so outdoor installation often use the slot fixed way, the need to cut and connect the place, the same method, and indoor installation, but need to be equipped with an additional waterproof adhesive to consolidate the connection point waterproof effect.

3, the power supply connection method:12v addressable RGB led strip is generally a low-voltage strip (DC12V), so you need to use a switching power supply, the size of the power supply according to the power of the LED strip and the length of the connection to determine the conventional strip is 5 meters a volume, if the demand is in more than 5 meters, you need to communicate with our customer service, custom program production, can not be used casually docking, resulting in voltage attenuation If the light beads are not working properly, the strip will gradually become darker, or even not bright.

4, controller connection: LED horse racing lights and led strip multi-color lights need to use the controller to achieve the effect of change, and the control distance of each controller is not the same, in general, the simple controller control distance of 10 to 15 meters, the remote controller control distance of 15 to 30 meters distance. If the LED strip is connected at a longer distance and the controller cannot control that long, then a power amplifier is needed to tap it.

1, product model: WS2811 5050 addressable led strip with 60leds/m
2, Light source: SMD 5050 LED;
3, Plate: FPCB;
4, Chip: Taiwan Epistar chip, and other chips in Taiwan;
5, IC model: WS2811, (1 meter 10 IC, 1 IC control 6 LED lights);
6, gray level: 256 levels, (1 meter 10 pixels);
7, the number of leds: 60 LEDs/ meter, each 1 light for a group, can be cut;
8、Lighting angle: 120 °;
9, light color: can be adjusted through the controller for white, red, yellow, blue, green, etc.;
10, the standard working voltage: DC 12V;
11, power: 14.4W ±10% / m;
12, waterproof level: not waterproof, drip glue (IP65), casing (IP67), casing solid grouting (IP68), etc..
13, Size of FPCB board: width: 10 mm, thickness: 3mm;
14, FPCB color: white, yellow, black (except white needs to be customized);
15, Packaging: 5 m / roll, back 3M adhesive behind the strip, static bag package;

Full-color light strip product description.
The light bar uses the world’s first external IC series of light beads to drive the light as one plus a 104 capacitor composition. The light bar panel looks very simple and beautiful, WS2811 is also a very stable performance, the brightness of the lamp beads is very high. High brightness, stable performance, simple and beautiful board, easy to produce, low cost, low failure rate. The ideal design choice for lighting outdoor lighting.

The main features of dream color led strip

1, control principle: an IC control ten LEDs to form a circuit (a group), the controller through the control IC to control the circuit inside the FPCB, so as to control the LED strip change different effects; such as flashing, chase, jumping change, clockwise running horse, counterclockwise running horse, monochrome running horse, color-changing running horse, single chase from beginning to end, flowing water, simulated lightning, etc.; the change effect of this light strip is not limited to the current controller built-in 94 kinds of effects, according to customer needs, their own preparation; row into the form of the screen can display, text, letters, pictures, animation, and so on.
2, environmental protection and safety: the use of high-quality high bright SMD 5050 LED. with low power consumption, generates little heat, no glare, impact resistance, and other characteristics. Low voltage DC 5V, 12V, 24V power supply, high safety, and reliability.
3, rich and diverse colors can be adjusted according to customer needs through the controller at will.
4、Long life span: average life span of 50,000 hours.
5、Cutting and welding is convenient and free: each group of LEDs can form a circuit and can be cut off and welded at will along the above cut line to meet the needs of customers’ requirements for various strip lengths.
6, soft: the use of soft FPCB board as the substrate, can be docked, bent, cut, and fixed at will in the concave and convex surface.
7, light, thin: suitable for installation in narrow spaces.

Application

1, hotels/nightclubs / KTV and other places of polygonal walls, teardrop rows of the ceiling, to decorate and set the atmosphere.
2, buildings, advertising walls, signboards, festivals, and other decorative areas of the city up the beauty/lighting effect.
3, home decoration lighting (stairs, door frame, bar, wine cooler, closet, TV cabinet, DIY home decoration …)
4, car beauty (car body, undercarriage …).
5、Iconic buildings building pavilion, bridges, parks, and other outlines of the outline, up to embellish the lighting effect.
6, lighting signals (such as a variety of luminous indication signs)
7、Edge-Lighting transparent or diffuse material
8, support in underwater lighting project
9、The edge of canopy and bridge arch/amusement park/theater/aircraft cockpit lighting

Color-changing light strip instructions.

1、Indoor installation: LED strip light for indoor installation is relatively simple, as it does not have to withstand the wind and rain. When installing, you can directly tear off the sticker on the 3M double-sided adhesive surface on the back of the strip, and then fix the strip in the place where it needs to be installed and press them flat. If you meet the corner of the strip is too long and too short, the LED strip can be cut or welded at any point in each group with scissors logo cut line alone.
2, outdoor installation: outdoor installation because it will be subject to wind and rain, can not be fixed with 3M adhesive, so the outdoor installation is often used slot fixed way, the need to cut and connect the place, the same method, and indoor installation, but need to be equipped with an additional waterproof adhesive to consolidate the waterproof effect of the connection point.
3, the power supply connection method: LED illumination strip general voltage DC24V, so you need to use a switching power supply, the size of the power supply according to the power of the LED strip, and the length of the connection to determine.
4、Controller connection method: LED runner strip and RGB full-color strip need to use the controller to realize the illusion effect, and the control distance of each controller is different, generally speaking, the control of simple controller is 40 to 50 meters, the control of remote controller is 80 to 90 meters, and the longest can control the strip up to 100 meters. If the LED strip is connected to a long-distance, and the controller can not control that long strip, then you need to use a power amplifier to tap.

Three-Way of connecting PW and mini controller

• This digital led strip has 60 pcs 5050 RGB LED per meter
• 20Pixels per meter, SPI control, 3LEDs per section
• Can be cut every 100mm, white & black PCB board are available
• 1+1 Ounce copper FPC, 5 m per reel, the 3M tape is included
• JST SM connector on each side, DC12V constant voltage operation
• Silicon coating, silicon tube housing, silicone injection waterproof

Strict Quality Assurance.

1: Striplight Any quality issue occurs within 365 days, with a free replacement service and no need to return defective products

2: Striplight extended period to 730 days, please contact me via the contact information on the card.(Whatsapp+8613267109053)

You can contact me at any time in any of the above three situations, or if you have good suggestions and ideas, you can contact me. Customer service will reply within 12 hours and solve the problem for you, I look forward to your message

Precautions

• Using voltage DC12V, higher than 12V will destroy it.
• If you need better-led strip performance, you can use an Android/IOS Bluetooth controller SP105E&SP110E, music controller CSY08&SP107E, WiFi controller SP108E, Alexa controller SP501E, or a programmable controller K-1000C. It also works with the Amazon Alexa controller.
• It is better to add DC12V voltage every 16.4FT because the LEDs at the far end of the strip might be dimmer due to the added resistance and voltage drop that occurs as the current flows to that end of the strip.
• The LED strip is made by 50cm FPCB, so there is a solder point each 50cm(1.6FT) on the strip. But this minor flaw has no bad effect on the strip’s performance. In fact, ALL the LED strips on the market are manufactured in half-meter lengths.

Package Detail:

1x 3 pin male connector for connector controller.
200x 16.4 ft WS2812B 150 LED strip, Box Size: 42.5*40*26cm, Weight is 13kg/box.